Driveway Calculator

Asphalt tons, gravel layers, concrete yards and sealer gallons.

Project Details
Enter your measurements and requirements
$
Results
Calculated estimates for your project
Area500 sq ft
Quantity10 tons of hot mix
Crushed stone base, 6 in15.5 tons
Estimated material cost$1,920

Turn these numbers into a build plan.

  • 500 sq ft area
  • 10.0 tons of hot mix quantity
  • $1,920 est. cost
Materials List
Recommended materials and quantities
Material10 tons of hot mix

Show your build

Finished the driveway? Snap a before and after. The photo maker lines them up into one image you can post, and a free Blueprint account keeps the photos with your measurements and materials.

Make a before and after
Project plan · built from your numbers

Asphalt driveway, 500 sq ft

10.0 tons of hot mix for 50 x 10 ft. Use this to check a contractor's quantities, or plan the prep yourself.

Materials
$1,920
Time
1 to 2 weeks
Level
Advanced
5 steps 4 tools 2 materials
  1. 1

    Check rules and call 811

    Ask about apron and permit rules at the street, then have utilities marked.

  2. 2

    Excavate and grade

    Remove soft soil and grade for drainage away from the garage.

  3. 3

    Build the base

    Compact the base in lifts until it does not move underfoot.

01 · Your numbers
Area
500 sq ft
Quantity
10.0 tons of hot mix
Est. cost
$1,920
02 · The plan

5 steps · 4 tools · 2 materials

2 more steps, the full tool list and a shopping list you can check off as you go.

03 · Finished

Your plan is 60% built. Save it.

3/5

Asphalt driveway, 500 sq ft

Finished in 1 to 2 weeks · $1,920 DIY

Built for your area of 500 sq ft. Your first plan saves free. No card needed.

Or save it with just your email

We send a link; open it and this plan is your first project. Your first plan saves free. No card needed.

Borrow these 4 tools from neighbors

How to estimate a driveway

Use these quantities to check a bid. For upkeep, see the driveway repair and sealing guide or the gravel calculator.

  1. Measure. Multiply length by width. Add aprons and turnarounds.
  2. Set the thickness. Residential asphalt is usually 2 to 3 in and concrete 4 to 5 in.
  3. Convert. Asphalt weighs about 145 lb per cu ft. Concrete is sold by the cubic yard.
  4. Add the base. Plan a compacted crushed stone base under asphalt or concrete.

Frequently asked questions

How many tons of asphalt do I need?

A 50 x 10 ft driveway at 3 in is 125 cu ft, about 9.1 tons before 5% extra. Order 10 tons.

How much sealer do I need?

About 1 gallon per 80 sq ft per coat. Porous or older asphalt takes more.

How thick should a concrete driveway be?

4 in is common for cars, with 5 to 6 in for heavier vehicles. Ask your local building department about apron rules.

Related calculators

All calculators

Gravel Calculator (Tons and Cubic Yards)

Tons, cubic yards and cost for any gravel or stone, any shape, with driveway layers and truck loads

Concrete Slab Calculator

Draw any slab shape and get a full materials list, tools, cost, and step-by-step plan

Concrete Calculator

Cubic yards, bags and cost for slabs, footings, walls, columns, stairs and curbs

Related cheat sheets

All cheat sheets

Concrete Cheat Sheet

Curing calculator with walk and drive-on dates, strength chart by temperature, mix ratios by PSI, bags per yard, control joints and weather rules

Masonry Joint Type Visual Guide

Visual reference illustrating common mortar joints and weather resistance advice

Retaining Wall Guide

Block selection, base preparation, drainage requirements, and height limitations

Plan the whole project

Turn these numbers into a full project plan

DIYProject.ai turns your measurements into an ordered task list, a complete materials list, and a priced shopping cart, then tracks your spend as you build. The calculators and cheat sheets stay free, no account required.

Get your free planPlan any project with AI